#1
|
||
|
Me’s got a problem
gday guys..............................Harrys at it again
I got a second pc which is the slave and it's connected to my main pc by a cross-over cable. It’s running with two hard drives, which I want to remove one and put it in the main pc. Can I just remove it and then reinstall it in my main pc? But the problem is my slave pc when I switch it on I get a beeping noise, it lasts for about 3 seconds then stops then start again and the monitor is receiving nothing! Need help asap……………………. |
#2
|
||
|
Well it depends if it's the drive you expect the main PC to boot off. If it is, then I wouldn't expect it to work. You'll probably have to re-install windows. Also, if it was the drive the old PC booted off, then it will of course have problems if it can't find it.
Check to see if it comes up in BIOS when you start the PC - you know, hold down F1 or DEL or whatever it says to go into setup mode right at the start when you boot up. |
#3
|
||
|
MUD THANKS, IVE LEFT THE MAIN HARD DRIVE IN THE SECOND PC. THE HARD DRIVE I REMOVED WAS THE SLAVE.
|
#4
|
||
|
Can't see any reason the old PC wouldn't work if you just took out the slave. Check the BIOS and see if it has a problem.
|
#5
|
||
|
ok will try tonite..................
|
#6
|
||
|
ok tried to start the pc with the windows cd in and still wont fire up , still just getting the beeping sound!
the monitor status is no signal thats what it say's on the screen. |
#7
|
||
|
err that doesn't sound good. Make sure everything is plugged back in (eg. video cable). If it is, open it up and look inside - maybe you bumped the video card or something else out of its slot.
|
#8
|
||
|
Yeah 3 beeps is 'usually' a video card problem, so like Mud said I'd check that first - take it out and plug it in properly again cause yeah it could've had a shove etc.
__________________
[WHC]Shady |
#9
|
||
|
mud i plug in the main pc's moniter to my second pc's vidoe card and no go! so i think the video card has shit its self on the second pc!
|
#10
|
||
|
can you inform me of a cheap video card for a asus mother board its a p3b-f ....................pentium lll 550. the old video card was a diamond viper v770
thanks |
#11
|
||
|
you want 3d capability? Maybe look for a Geforce 2 or something
|
#12
|
||
|
yeah thanks again mud!
|
#13
|
||
|
ok would these be ok with my asus P3B-F motherboard ?
64MB GIGA-BYTE ATI7000 - $53 OR 64M Winfast-A180T GF4 MX440 8x DDR W/TV - $ 68 |
#14
|
||
|
dunno what the 1st one is, 2nd one sounds ok
|
#15
|
||
|
Give up and buy an Etch-a-sketch
Slaide |
#16
|
||
|
roflmao..........................
|
#17
|
||
|
Easy to reboot....
1. Turn Etch-a-sketch upside down. (So lcd screen is facing the ground) 2. Shake Etch-a-sketch vigorously. 3. Be careful not to drop Etch-a-sketch while rebooting. This may cause internal damage Slaide |
#18
|
||
|
how many polygons can it draw per second?
|
#19
|
||
|
As fast as your fingers can twitch.
Slaide |
#20
|
||
|
my x-girlfriend said i could twitch very fast at times!
is that fast enuff? |
#21
|
||
|
Knowing of your elephant-like reflexes, I think I can imagine why she's your ex-girlfiend..
Slaide |
#22
|
||
|
hahaha btw ivw got the second pc up and running again!
|
#23
|
||
|
Harry - If you ever have to call a helpdesk for tech support - put me on conference call.
I'd luv to hear that.
__________________
WHC's ACE website |
#24
|
||
|
I never need to call for help I just come here!
|
#25
|
||
|
LOL..
Us help?!? Slaide |
#26
|
||
|
yes you are a gr8 help simon........................... :-)
|
#27
|
||
|
Slaide - I noticed that creek down from you turned itself into a raging river the other night.
__________________
WHC's ACE website |
#28
|
||
|
Yes.. It often does that when there is some rain.
A few kids were actually body boarding down the stream. Slaide |
#29
|
||
|
BullSh|t..........................
|
#30
|
||
|
that's not very nice harry..
Slaide |
Thread Tools | Search this Thread |
Display Modes | |
|
|